TDA1011 2 to 6 W audio power amplifier

Description:

The TDA1011 is a monolithic integrated audio amplifier circuit in a 9-lead single in-line (SIL) plastic package. The device is especially designed for portable radio and recorder applications and delivers up to 4 W in a 4Ω load impedance. The device can deliver up to 6 W into 4Ω at 16 V loaded supply in mains-fed applications. The maximum permissible supply voltage of 24 V makes this circuit very suitable for d.c. and a.c. apparatus, while the very low applicable supply voltage of 3,6 V permits 6 V applications.

Special features:

single in-line (SIL) construction for easy mounting
separated preamplifier and power amplifier
high output power
thermal protection
high input impedance
low current drain
limited noise behaviour at radio frequencies

Reference:

Supply voltage range Vp...........................3,6 to 20 V
Repetitive peak output current IORM...........max. 3 A
Operating ambient temperature Tamb ........−25 to + 150 °C
Storage temperature Tstg ........................−55 to + 150 °C

Circuit diagram:

TDA1011 circuit diagram

TDA1011 layout

TDA1011 pcb

Datasheet for TDA1011A: Download

Where you can buy: Aliexpress

Comments

200W Hybrid Audio Amplifier Circuit

200W Hybrid Audio Amplifier Circuit - c onnecting two TDA2030 thru cheap power transistors we can create a amplifier wich can deliver a higher power. With the components value from the schematic the total amplifier gain is 32 dB. The speaker can be 2 ohm instead of 4 ohm if we use the TIP transistors. TDA 2030 is produced by SGS Ates and is a complete audio amplifier. AB class of the final amplifier cand deliver up to 14W on 4 ohm at a +-14V power supply. With a proper designed power supply this audio amplifier can output 200W. Active components: IC1, Ic2 TDA 2030 T1, T3 = BD 250, TIP 36 T2,T4 = BD 249, TIP 35 D1 … D4 = 1N4001 200W Hybrid Audio Amplifier Circuit

2 x 15 W stereo Bridge Tied Load (BTL) audio amplifier

General description: The TDA8946J is a dual-channel audio power amplifier with an output power of 2 × 15 W at an 8 Ω load and a 18 V supply. The circuit contains two Bridge Tied Load (BTL) amplifiers with an all-NPN output stage and standby/mute logic. The TDA8946J comes in a 17-pin DIL-bent-SIL (DBS) power package. The TDA8946J is printed-circuit board (PCB) compatible with all other types in the TDA894x family. One PCB footprint accommodates both the mono and the stereo products. Features: Few external components Fixed gain Standby and mute mode No on/off switching plops Low standby current High supply voltage ripple rejection Outputs short-circuit protected to ground, supply and across the load Thermally protected Printed-circuit board compatible Circuit Diagram: Circuit Diagram for 2 x 15 W stereo Bridge Tied Load (BTL) audio amplifier PCB layout: PCB layout TDA8946 Datasheet for TDA8946J: Download

Multifunction quad power amplifier with built-in diagnostics features

Features: Multipower BCD technology DMOS power output High output power capability 4 x 25 W / 4  @ 14.4 V, 1 kHz, 10 % THD, 4 x 35 W EIAJ Max. output power 4 x 60 W / 2  Full I2C bus driving: Standby Independent front/rear soft play/mute Selectable gain 26 dB - 12 dB (for low noise line output function) I2C bus digital diagnostics Full fault protection DC offset detection Four independent short circuit protection Clipping detector ESD protection Description: The TDA7561 is a BCD technology quad bridge type of car radio amplifier in Flexiwatt25 package specially intended for car radio applications. Thanks to the DMOS output stage the TDA7561 has a very low distortion allowing a clear powerful sound. This device is equipped with a full diagnostics array that communicates the status of each speaker through the I2C bus.The possibility to control the configuration and behaviour of the ...

AmplifierCircuits

Search This Blog