AmplifierCircuits

TDA1566   g eneral description: The TDA1566 is a car audio power amplifier with a complementary output stage realized in BCDMOS. The TDA1566 has two Bridge Tied Load (BTL) output stages and comes in a HSOP24 or DBS27P package. The TDA1566 can be controlled with or without I2C-bus. With I2C-bus control gain settings per channel and diagnostic trigger levels can be selected. Failure conditions as well as load identification can be read with I2C-bus. The load identification detects whether the outputs of a BTL channel are connected with a DC or AC load and discriminates between a speaker load, a line driver load and an open (unconnected) load. The TDA1566 can be configured in a single BTL mode and drive a 1 Ω load. For the single BTL mode it is necessary to connect on the Printed-Circuit Board (PCB) the outputs of both BTL channels in parallel.   TDA1566 Audio Amplifier 2x46W / 1x92W TDA1566  features : Operates in I2C-bus mode and non-I2C-bus mode TH vers...

TDA8569Q  g eneral description: The TDA8569Q is an integrated class-B output amplifier in a 23-lead Single-In-Line (SIL) plastic power package. It contains four amplifiers in Bridge-Tied Load (BTL) configuration, each with a gain of 26 dB. The output power is 4 × 40 W in a 2 Ω load.   TDA8569Q Audio Amplifier 4 x 40W TDA8569Q  features: Capable of driving 2 Ω loads Requires very few external components High output power Low output offset voltage Fixed gain Diagnostic facility (distortion, short-circuit and temperature pre-warning) Good ripple rejection Mode select switch (operating, mute and standby) Load dump protection Short-circuit safe to ground, to VP and across the load Low power dissipation in any short-circuit condition Thermally protected Reverse polarity safe Electrostatic discharge protection No switch-on/switch-off plop Flexible leads Low thermal resistance Pin compatible with the TDA8567Q. TDA8569Q  c...

TDA8950 g eneral description: The TDA8950 is a high-efficiency Class D audio power amplifier. The typical output power is 2 × 150 W with a speaker load impedance of 4 Ω. The TDA8950 is available in both HSOP24 and DBS23P power packages. The amplifier operates over a wide supply voltage range from ±12.5 V to ±40 V and features low quiescent current consumption.  TDA8950 Audio Amplifier 2x150W TDA8950 features: Pin compatible with TDA8920B for both HSOP24 and DBS23P packages Symmetrical operating supply voltage range from ±12.5 V to ±40 V Stereo full differential inputs, can be used as stereo Single-Ended (SE) or mono Bridge-Tied Load (BTL) amplifier High output power in typical applications: SE 2 × 150 W, RL 4 Ω (VP = ±37 V) SE 2 × 170 W, RL 4 Ω (VP = ±39 V) SE 2 × 100 W, RL 6 Ω (VP = ±37 V) BTL 1 × 300 W, RL 8 Ω (VP = ±37 V) Low noise Smooth pop noise-free start-up and switch off Zero dead time switching Fixed frequency Internal or external clock H...

TDA1514A  g eneral description: Here the very simple but powerful amplifier kit which built based on TDA1514A amplifier chip. The circuit is for single channel only, you should build two similar circuit for stereo application. A heatsink is a must to be attached on the IC TDA1514A. This circuit can be used as well as stereoamplifiers Bass in a 5.1 system.  TDA1514A Audio Amplifier 50W TDA1514A  features : Battery operation Minimum external parts Wide supply voltage range: 4V–12V or 5V–18V Low quiescent current drain: 4mA Voltage gains from 20 to 200 Ground referenced input Self-centering output quiescent voltage Low distortion: 0.2% (AV = 20, VS = 6V, RL = 8Ω, PO = 125mW, f = 1kHz) Available in 8 pin MSOP package TDA1514A  circuit : TDA1514A Audio Amplifier 50W TDA1514A  layout : Printed Circuit Layout and placement for mono 40 W amplifier: TDA1514A Audio Amplifier 50W pcb TDA1514A Audio Amplifier 50W la...

TDA2005 description: The TDA2005 is a class B dual audio power amplifier in Multiwatt11 package specifically designed for car radio applications. Power booster amplifiers can be easily designed  using this device that provides a high current  capability (up to 3.5 A) and can drive very low  impedance loads (down to 1.6  in stereo  applications) obtaining an output power of more than 20 W (bridge configuration).  TDA2005 Audio Amplifier 2x10w TDA2005 features: High output power: Po = 10 + 10 W @ RL = 2 , THD = 10 % Po = 20 W @ RL = 4 , THD = 10 %. Protection against: Output DC and AC short circuit to ground Overrating chip temperature Load dump voltage surge Fortuitous open ground Very inductive loads Loudspeaker protection during short circuit for one wire to ground TDA2005 circuit diagram: TDA2005 Audio Amplifier 2x10w TDA2005 layout: PCB TDA2005 Audio Amplifier 2x10w Layout TDA2005 Audio Amplifier 2x10w...