Skip to main content

Microphone Preamplifier

This is a good pre-amplifier for microphones that can be. Used in, for example, mixing consoles The circuit operates with a dual op-amp type NE 5532. The amplifier must be adjusted. Simply plug the power and control over P1 such that half the supply voltage (6 V) on pin 3 of IC1 state. P2 is then adjusted to the desired volume.
  • R1 = 8,2 kW
  • R2, R4, R5, R6 = 10 kW
  • R3 = 1 k
  • P1 = 4.7 K?
  • P2 = 100 k
  • C1, C2, C4, C6 = 10 uF
  • C3 = 470 nF
  • C5 = 100 nF
  • IC1 NE = 5532

Labels:

Comments

Post a Comment

Popular posts from this blog

200W Hybrid Audio Amplifier Circuit

200W Hybrid Audio Amplifier Circuit - c onnecting two TDA2030 thru cheap power transistors we can create a amplifier wich can deliver a higher power. With the components value from the schematic the total amplifier gain is 32 dB. The speaker can be 2 ohm instead of 4 ohm if we use the TIP transistors. TDA 2030 is produced by SGS Ates and is a complete audio amplifier. AB class of the final amplifier cand deliver up to 14W on 4 ohm at a +-14V power supply. With a proper designed power supply this audio amplifier can output 200W. Active components: IC1, Ic2 TDA 2030 T1, T3 = BD 250, TIP 36 T2,T4 = BD 249, TIP 35 D1 … D4 = 1N4001 200W Hybrid Audio Amplifier Circuit
2 comments
Read more

2 x 15 W stereo Bridge Tied Load (BTL) audio amplifier

General description: The TDA8946J is a dual-channel audio power amplifier with an output power of 2 × 15 W at an 8 Ω load and a 18 V supply. The circuit contains two Bridge Tied Load (BTL) amplifiers with an all-NPN output stage and standby/mute logic. The TDA8946J comes in a 17-pin DIL-bent-SIL (DBS) power package. The TDA8946J is printed-circuit board (PCB) compatible with all other types in the TDA894x family. One PCB footprint accommodates both the mono and the stereo products. Features: Few external components Fixed gain Standby and mute mode No on/off switching plops Low standby current High supply voltage ripple rejection Outputs short-circuit protected to ground, supply and across the load Thermally protected Printed-circuit board compatible Circuit Diagram: Circuit Diagram for 2 x 15 W stereo Bridge Tied Load (BTL) audio amplifier PCB layout: PCB layout TDA8946 Datasheet for TDA8946J:   Download
Post a Comment
Read more

Multifunction quad power amplifier with built-in diagnostics features

Features: Multipower BCD technology DMOS power output High output power capability 4 x 25 W / 4  @  14.4 V, 1 kHz, 10 % THD, 4 x 35 W EIAJ Max. output power 4 x 60 W / 2  Full I2C bus driving: Standby Independent front/rear soft play/mute Selectable gain 26 dB - 12 dB (for low noise  line output function) I2C bus digital diagnostics Full fault protection DC offset detection Four independent short circuit protection Clipping detector ESD protection Description: The TDA7561 is a BCD technology quad bridge type of car radio amplifier in Flexiwatt25 package  specially intended for car radio applications.  Thanks to the DMOS output stage the TDA7561   has a very low distortion allowing a clear powerful   sound.  This device is equipped with a full diagnostics  array that communicates the status of each   speaker through the I2C bus.The possibility to  control the configuration and behaviour of the ...
Post a Comment
Read more