Power Amplifier 300W

POWER OUTPUT:

200W rms/8 ohm
310W rms/4 ohm
800W rms/8 ohm (Bridge mode)

FREQUENCE RESPONSE

20HZ-20KHZ +/-0.5dB

INPUT SENSITIVITY

1V for 200W/300W

HUM AND NOISE

-105dB

THD

<0.1%

DAMPING FACTOR

Part list:

R1-19= 1Kohm 5W	R34-35= 0.1ohm 5W	C14-17= 100uF 100V
R2-3= 4.7Kohm	R36-43= 39ohm	C15= 100nF 250V polyester
R4-5= 22ohm	R37-42= 5.6Kohm 1W	Q1-2-3= BC547
R6-14= 10Kohm	R38-41= 220ohm 5W	Q4-5-6= BC557
R7-8= 1Kohm	R39-40= 0.1ohm 5W	Q7-11-12= BD140 or BC640
R9-23*=10K ohm	R44-45= 0.1ohm 5W	Q8= BC549
R10= 10ohm *see circuit sch.	R46= 4.7ohm 2W	Q9-10-15= BD139 or BC639
R11-13= 2.2Kohm	R47= 100ohm	Q13-14= MJ15004
R12= 22Kohm	C1= 2.2uF 25V	Q16-17= MJ15003
R15-16= 22ohm	C2-6= 330pF ceramic	TR1= 2K2 Trimmer
R17-18= 4.7Kohm	C3-8= 100uF 100V	F1-2= 5A Fuse Fast
R20-25= 390ohm	C4-9= 100nF 250V	D1-3= 5.1V 0.5W Zener
R21= 6.8Kohm	C5= 100nF 100V polyester	D2= 62V/5W Zener or 47v and 15V in series
R22= 4.7Kohm	C7= 100uF 25V	D4-5= 1N4004
R24-26-33= 220ohm	C10= 1.5nF 100V polyester	L1=10 turns diameter 1mm in 15mm diameter tube
R27-32= 100ohm 1W	C11-12= 1.5nF 100V polyester	L1=10 turns diameter 1mm in 15mm diameter tube
R28,29,30,31= 100ohm	C13-16= 100nF 250V polyester	*Use R23=6k8 for 4 ohm loudspeakers

Comments

One Chip AM/FM Radio with Audio Power Amplifier

Description: The integrated circuit TDA1083 includes, with exception of the FM front end, a complete AM-/FM-radio-circuit with audio power amplifier. An internal Z-diode stabilizes the supply voltage at VS 13 V, which allows with the aid of a resistor and a rectifier, the circuit to be driven by a higher external supply voltage. Features: Large supply voltage range VS = 3 to 12 V High AM-Sensitivity Limiting threshold voltage Vi = 50 V Audio output power P0 = 0.7 W AFC-connection for VHF-tuner AM-FM switching without high frequency voltages Applications: AM-/FM- and audio-amplifier Circuit Diagram: Circuit diagram for One Chip AM/FM Radio with Audio Power Amplifier Datasheet for TDA1083: Download

2 x 15 W stereo Bridge Tied Load (BTL) audio amplifier

General description: The TDA8946J is a dual-channel audio power amplifier with an output power of 2 × 15 W at an 8 Ω load and a 18 V supply. The circuit contains two Bridge Tied Load (BTL) amplifiers with an all-NPN output stage and standby/mute logic. The TDA8946J comes in a 17-pin DIL-bent-SIL (DBS) power package. The TDA8946J is printed-circuit board (PCB) compatible with all other types in the TDA894x family. One PCB footprint accommodates both the mono and the stereo products. Features: Few external components Fixed gain Standby and mute mode No on/off switching plops Low standby current High supply voltage ripple rejection Outputs short-circuit protected to ground, supply and across the load Thermally protected Printed-circuit board compatible Circuit Diagram: Circuit Diagram for 2 x 15 W stereo Bridge Tied Load (BTL) audio amplifier PCB layout: PCB layout TDA8946 Datasheet for TDA8946J: Download

200W Hybrid Audio Amplifier Circuit

200W Hybrid Audio Amplifier Circuit - c onnecting two TDA2030 thru cheap power transistors we can create a amplifier wich can deliver a higher power. With the components value from the schematic the total amplifier gain is 32 dB. The speaker can be 2 ohm instead of 4 ohm if we use the TIP transistors. TDA 2030 is produced by SGS Ates and is a complete audio amplifier. AB class of the final amplifier cand deliver up to 14W on 4 ohm at a +-14V power supply. With a proper designed power supply this audio amplifier can output 200W. Active components: IC1, Ic2 TDA 2030 T1, T3 = BD 250, TIP 36 T2,T4 = BD 249, TIP 35 D1 … D4 = 1N4001 200W Hybrid Audio Amplifier Circuit

AmplifierCircuits

Search This Blog