Skip to main content

200W Subwoofer Amplifier Circuit

Circuit Description

Here is a circuit that uses a mosfet amplifier amplicable for subwoofer as the main booster, or the basis of this boosterAmplifier. Circuit which uses MOSFET Power Amplifier is powered by the output more than 200W Speaker 8 Ohm impedance. We also include a suitable power supply circuit with the use of MOSFETamplifier with 200W of power, not only of his course Schematic diagram for the layout design is also already there.

Amplifier Circuit Diagram

Amplifier Circuit Diagram
200W Mosfet Amplifier LAyout PCB
200W Mosfet Amplifier LAyout PCB

Regulator Circuit Diagram MOSFET AMPLIFIER
Regulator Circuit Diagram MOSFET AMPLIFIER
Regulator PCB MOSFET amplifier
Regulator PCB MOSFET amplifier

Labels

Labels:
Location: North America

Comments

  1. Anonymous7/06/2014 05:29:00 PM

    I for all time emailed this blog pos page to all my contacts, because if like to read it afterward my
    frirnds wll too.

    my homepage - home renovation tips

    ReplyDelete
  2. Anonymous7/21/2014 12:02:00 PM

    i want to make this amplifier please send my the pcb diagram and schematics to adrian99fm@gmail.com
    thank you

    ReplyDelete
  3. Unknown11/10/2015 10:51:00 AM

    S' il vous plaît :rms

    ReplyDelete
  4. Daly motion11/15/2015 08:33:00 AM

    Help mi 2ic la4440 joint 1 output digram plz.sent plole94@gmail.com

    ReplyDelete
  5. Unknown4/24/2018 02:31:00 AM

    pcb print out is not seen just help plz

    ReplyDelete
  6. Anil2/22/2019 01:37:00 AM

    Silicon chip magazine article

    ReplyDelete
  7. Anil2/22/2019 01:41:00 AM

    What is the idle current (through the output transistors) of this amp?

    ReplyDelete
  8. Unknown11/19/2019 06:23:00 PM

    Sir, how can get jit pdf file sir?

    ReplyDelete
  9. obaghi5/04/2020 02:28:00 PM

    Nice post.. thank a would save this JPEG to make it

    ReplyDelete

Post a Comment

Popular posts from this blog

One Chip AM/FM Radio with Audio Power Amplifier

Description: The integrated circuit TDA1083 includes, with exception  of the FM front end, a complete AM-/FM-radio-circuit  with audio power amplifier. An internal Z-diode  stabilizes the supply voltage at VS 13 V, which allows  with the aid of a resistor and a rectifier, the circuit to be  driven by a higher external supply voltage. Features: Large supply voltage range VS = 3 to 12 V High AM-Sensitivity Limiting threshold voltage Vi = 50 V Audio output power P0 = 0.7 W AFC-connection for VHF-tuner AM-FM switching without high frequency voltages Applications: AM-/FM- and audio-amplifier Circuit Diagram: Circuit diagram for One Chip AM/FM Radio with Audio Power Amplifier Datasheet for TDA1083:   Download
2 comments
Read more

2 x 15 W stereo Bridge Tied Load (BTL) audio amplifier

General description: The TDA8946J is a dual-channel audio power amplifier with an output power of 2 × 15 W at an 8 Ω load and a 18 V supply. The circuit contains two Bridge Tied Load (BTL) amplifiers with an all-NPN output stage and standby/mute logic. The TDA8946J comes in a 17-pin DIL-bent-SIL (DBS) power package. The TDA8946J is printed-circuit board (PCB) compatible with all other types in the TDA894x family. One PCB footprint accommodates both the mono and the stereo products. Features: Few external components Fixed gain Standby and mute mode No on/off switching plops Low standby current High supply voltage ripple rejection Outputs short-circuit protected to ground, supply and across the load Thermally protected Printed-circuit board compatible Circuit Diagram: Circuit Diagram for 2 x 15 W stereo Bridge Tied Load (BTL) audio amplifier PCB layout: PCB layout TDA8946 Datasheet for TDA8946J:   Download
Post a Comment
Read more

200W Hybrid Audio Amplifier Circuit

200W Hybrid Audio Amplifier Circuit - c onnecting two TDA2030 thru cheap power transistors we can create a amplifier wich can deliver a higher power. With the components value from the schematic the total amplifier gain is 32 dB. The speaker can be 2 ohm instead of 4 ohm if we use the TIP transistors. TDA 2030 is produced by SGS Ates and is a complete audio amplifier. AB class of the final amplifier cand deliver up to 14W on 4 ohm at a +-14V power supply. With a proper designed power supply this audio amplifier can output 200W. Active components: IC1, Ic2 TDA 2030 T1, T3 = BD 250, TIP 36 T2,T4 = BD 249, TIP 35 D1 … D4 = 1N4001 200W Hybrid Audio Amplifier Circuit
2 comments
Read more