Skip to main content

Programming tutorial adc ARM Microcontrollers

So, the microcontrollers today offering a more and simple solution our lives. One of the controllores is LPC11Cx2. The LPC11Cx2/Cx4 are an ARM Cortex-M0 based, low-cost 32-bit MCU family, designed  for 8/16-bit microcontroller applications, offering performance, low power, simple instruction set and memory addressing together with reduced code size compared to existing 8/16-bit architectures.The LPC11Cx2/Cx4 operate at CPU frequencies of up to 50 MHz. The peripheral complement of the LPC11Cx2/Cx4 includes 16/32 kB of flash memory, 8 kB of data memory, one C_CAN controller, one Fast-mode Plus I2C-bus interface, one RS-485/EIA-485 UART, two SPI interfaces with SSP features, four general purpose counter/timers, a 10-bit ADC, and up to 40 general purpose I/O pins.On-chip C_CAN drivers and flash In-System Programming tools via C_CAN are included. In addition, the LPC11C22 and LPC11C24 parts include an on-chip, high-speed CAN transceiver. 
Programming tutorial adc ARM Microcontrollers
Programming tutorial adc ARM Microcontrollers
One of intereting article you can find here www.gadgetronicx.com 
Labels:

Comments

Post a Comment

Popular posts from this blog

200W Hybrid Audio Amplifier Circuit

200W Hybrid Audio Amplifier Circuit - c onnecting two TDA2030 thru cheap power transistors we can create a amplifier wich can deliver a higher power. With the components value from the schematic the total amplifier gain is 32 dB. The speaker can be 2 ohm instead of 4 ohm if we use the TIP transistors. TDA 2030 is produced by SGS Ates and is a complete audio amplifier. AB class of the final amplifier cand deliver up to 14W on 4 ohm at a +-14V power supply. With a proper designed power supply this audio amplifier can output 200W. Active components: IC1, Ic2 TDA 2030 T1, T3 = BD 250, TIP 36 T2,T4 = BD 249, TIP 35 D1 … D4 = 1N4001 200W Hybrid Audio Amplifier Circuit
2 comments
Read more

2 x 15 W stereo Bridge Tied Load (BTL) audio amplifier

General description: The TDA8946J is a dual-channel audio power amplifier with an output power of 2 × 15 W at an 8 Ω load and a 18 V supply. The circuit contains two Bridge Tied Load (BTL) amplifiers with an all-NPN output stage and standby/mute logic. The TDA8946J comes in a 17-pin DIL-bent-SIL (DBS) power package. The TDA8946J is printed-circuit board (PCB) compatible with all other types in the TDA894x family. One PCB footprint accommodates both the mono and the stereo products. Features: Few external components Fixed gain Standby and mute mode No on/off switching plops Low standby current High supply voltage ripple rejection Outputs short-circuit protected to ground, supply and across the load Thermally protected Printed-circuit board compatible Circuit Diagram: Circuit Diagram for 2 x 15 W stereo Bridge Tied Load (BTL) audio amplifier PCB layout: PCB layout TDA8946 Datasheet for TDA8946J:   Download
Post a Comment
Read more

Multifunction quad power amplifier with built-in diagnostics features

Features: Multipower BCD technology DMOS power output High output power capability 4 x 25 W / 4  @  14.4 V, 1 kHz, 10 % THD, 4 x 35 W EIAJ Max. output power 4 x 60 W / 2  Full I2C bus driving: Standby Independent front/rear soft play/mute Selectable gain 26 dB - 12 dB (for low noise  line output function) I2C bus digital diagnostics Full fault protection DC offset detection Four independent short circuit protection Clipping detector ESD protection Description: The TDA7561 is a BCD technology quad bridge type of car radio amplifier in Flexiwatt25 package  specially intended for car radio applications.  Thanks to the DMOS output stage the TDA7561   has a very low distortion allowing a clear powerful   sound.  This device is equipped with a full diagnostics  array that communicates the status of each   speaker through the I2C bus.The possibility to  control the configuration and behaviour of the ...
Post a Comment
Read more