Skip to main content

LM4910 Stereo Headphone Amplifier

Circuit description:    

      LM4910 belonging to the Boomer series of National Semiconductors is an integrated stereo amplifier primarily intended for stereo headphone applications. The IC can be operated from 3.3V ans its can deliver 0.35mW output power into a 32 ohm load. The LM4910 has very low distortion ( less than 1%) and the shutdown current is less than 1uA. This low shut down current makes it suitable for battery operated applications. The IC is so designed that there is no need of the output coupling capacitors, half supply by-pass capacitors and bootstrap capacitors. Other features of the IC are turn ON/OFF click elimination, externally programmable gain etc.

Circuit diagram:  

     Circuit diagram of the LM4910 stereo headphone amplifier is shown above.C1 and C2 are the input DC decoupling capacitors for the left and right input channels. R1 and R2 are the respective input resistors. R3 is the feed back resistor for left channel while R4 is the feed back resistor for the right channel. C3 is the power supply filter capacitor. The feedback resistors also sets the closed loop gain in conjunction with the corresponding input resistors.

The IC is available only in SMD packages and care must be taken while soldering. 
The circuit can be powered from anything between 2.2V to 5V DC. 
The load can be a 32 ohm headphone. 
Absolute maximum supply voltage is 6V and anything above it will destroy the IC. 
A logic low voltage at the shutdown pins shut downs the IC and a logic high voltage at the same pin activates the IC. Original aritcle sourse circuitsproject.com
Labels:

Comments

Post a Comment

Popular posts from this blog

200W Hybrid Audio Amplifier Circuit

200W Hybrid Audio Amplifier Circuit - c onnecting two TDA2030 thru cheap power transistors we can create a amplifier wich can deliver a higher power. With the components value from the schematic the total amplifier gain is 32 dB. The speaker can be 2 ohm instead of 4 ohm if we use the TIP transistors. TDA 2030 is produced by SGS Ates and is a complete audio amplifier. AB class of the final amplifier cand deliver up to 14W on 4 ohm at a +-14V power supply. With a proper designed power supply this audio amplifier can output 200W. Active components: IC1, Ic2 TDA 2030 T1, T3 = BD 250, TIP 36 T2,T4 = BD 249, TIP 35 D1 … D4 = 1N4001 200W Hybrid Audio Amplifier Circuit
2 comments
Read more

2 x 15 W stereo Bridge Tied Load (BTL) audio amplifier

General description: The TDA8946J is a dual-channel audio power amplifier with an output power of 2 × 15 W at an 8 Ω load and a 18 V supply. The circuit contains two Bridge Tied Load (BTL) amplifiers with an all-NPN output stage and standby/mute logic. The TDA8946J comes in a 17-pin DIL-bent-SIL (DBS) power package. The TDA8946J is printed-circuit board (PCB) compatible with all other types in the TDA894x family. One PCB footprint accommodates both the mono and the stereo products. Features: Few external components Fixed gain Standby and mute mode No on/off switching plops Low standby current High supply voltage ripple rejection Outputs short-circuit protected to ground, supply and across the load Thermally protected Printed-circuit board compatible Circuit Diagram: Circuit Diagram for 2 x 15 W stereo Bridge Tied Load (BTL) audio amplifier PCB layout: PCB layout TDA8946 Datasheet for TDA8946J:   Download
Post a Comment
Read more

Multifunction quad power amplifier with built-in diagnostics features

Features: Multipower BCD technology DMOS power output High output power capability 4 x 25 W / 4  @  14.4 V, 1 kHz, 10 % THD, 4 x 35 W EIAJ Max. output power 4 x 60 W / 2  Full I2C bus driving: Standby Independent front/rear soft play/mute Selectable gain 26 dB - 12 dB (for low noise  line output function) I2C bus digital diagnostics Full fault protection DC offset detection Four independent short circuit protection Clipping detector ESD protection Description: The TDA7561 is a BCD technology quad bridge type of car radio amplifier in Flexiwatt25 package  specially intended for car radio applications.  Thanks to the DMOS output stage the TDA7561   has a very low distortion allowing a clear powerful   sound.  This device is equipped with a full diagnostics  array that communicates the status of each   speaker through the I2C bus.The possibility to  control the configuration and behaviour of the ...
Post a Comment
Read more