70 Watt Guitar Amplifier

Guitar Amplifier description:

Guitar Amplifier parts list:

R1______________18K 1/4W Resistor

R2_______________3K9 1/4W Resistor

R3,R6____________1K 1/4W Resistors

R4_______________2K2 1/4W Resistor

R5______________15K 1/4W Resistor

R7______________22K 1/4W Resistor

R8_____________330R 1/4W Resistor

R9,R10__________10R 1/4W Resistors

R11,R12_________47R 1/4W Resistors

R13_____________10R 1W Resistor

C1_______________1µF 63V Polyester Capacitor

C2_____________470pF 63V Polystyrene or Ceramic Capacitor

C3______________47µF 25V Electrolytic Capacitor

C4______________15pF 63V Polystyrene or Ceramic Capacitor

C5_____________220nF 100V Polyester Capacitor

C6_____________100nF 63V Polyester Capacitor

D1,D2,D3,D4___1N4148 75V 150mA Diodes

Q1,Q2________BC560C 45V 100mA Low noise High gain PNP Transistors

Q3,Q4________BC556 65V 100mA PNP Transistors

Q5___________BC546 65V 100mA NPN Transistor

Q6___________BD139 80V 1.5A NPN Transistor

Q7___________BD140 80V 1.5A PNP Transistor

Q8__________MJ2955 60V 15A PNP Transistor

Comments

200W Hybrid Audio Amplifier Circuit

200W Hybrid Audio Amplifier Circuit - c onnecting two TDA2030 thru cheap power transistors we can create a amplifier wich can deliver a higher power. With the components value from the schematic the total amplifier gain is 32 dB. The speaker can be 2 ohm instead of 4 ohm if we use the TIP transistors. TDA 2030 is produced by SGS Ates and is a complete audio amplifier. AB class of the final amplifier cand deliver up to 14W on 4 ohm at a +-14V power supply. With a proper designed power supply this audio amplifier can output 200W. Active components: IC1, Ic2 TDA 2030 T1, T3 = BD 250, TIP 36 T2,T4 = BD 249, TIP 35 D1 … D4 = 1N4001 200W Hybrid Audio Amplifier Circuit

2 x 15 W stereo Bridge Tied Load (BTL) audio amplifier

General description: The TDA8946J is a dual-channel audio power amplifier with an output power of 2 × 15 W at an 8 Ω load and a 18 V supply. The circuit contains two Bridge Tied Load (BTL) amplifiers with an all-NPN output stage and standby/mute logic. The TDA8946J comes in a 17-pin DIL-bent-SIL (DBS) power package. The TDA8946J is printed-circuit board (PCB) compatible with all other types in the TDA894x family. One PCB footprint accommodates both the mono and the stereo products. Features: Few external components Fixed gain Standby and mute mode No on/off switching plops Low standby current High supply voltage ripple rejection Outputs short-circuit protected to ground, supply and across the load Thermally protected Printed-circuit board compatible Circuit Diagram: Circuit Diagram for 2 x 15 W stereo Bridge Tied Load (BTL) audio amplifier PCB layout: PCB layout TDA8946 Datasheet for TDA8946J: Download

Multifunction quad power amplifier with built-in diagnostics features

Features: Multipower BCD technology DMOS power output High output power capability 4 x 25 W / 4  @ 14.4 V, 1 kHz, 10 % THD, 4 x 35 W EIAJ Max. output power 4 x 60 W / 2  Full I2C bus driving: Standby Independent front/rear soft play/mute Selectable gain 26 dB - 12 dB (for low noise line output function) I2C bus digital diagnostics Full fault protection DC offset detection Four independent short circuit protection Clipping detector ESD protection Description: The TDA7561 is a BCD technology quad bridge type of car radio amplifier in Flexiwatt25 package specially intended for car radio applications. Thanks to the DMOS output stage the TDA7561 has a very low distortion allowing a clear powerful sound. This device is equipped with a full diagnostics array that communicates the status of each speaker through the I2C bus.The possibility to control the configuration and behaviour of the ...

AmplifierCircuits

Search This Blog