4x7W OR 2x22W CAR RADIO POWER AMPLIFIER

Features:

HIGH OUTPUT POWER CAPABILITY:
4 x 9.5W OR 2 x 32W/4Ω MAX
4 x 8.5W OR 2 x 28W/4Ω EIAJ
4 x 7W OR 2 x 22W/4Ω @14.4V,1KHz; 10%
MINIMIZED EXTERNAL COUNT
- NO NEED OF DECOUPLING CAPACITORS
- NO NEED OF BOOTSTRAP CAPACITOR
- NO NEED OF EXTERNAL COMPENSATION
- INTERNALLY FIXED GAIN (20dB)
POP-FREE AUDIO SECTION
ST-BY FUNCTION (C-MOS)
MUTE FUNCTION (C-MOS)
CLIP DETECTOR, THERMAL WARNING,
SHORT CIRCUIT DETECTION
BUILT-IN VOLTAGE REGULATORS:
- 5V @ 150mA WITH RESET
- 5V @ 500mA WITH ST-BY
- 8.5V @ 200mA WITH ST-BY

Circuit Diagram:

TDA7451 2x22 W

TDA7451 4x7W

Comments

One Chip AM/FM Radio with Audio Power Amplifier

Description: The integrated circuit TDA1083 includes, with exception of the FM front end, a complete AM-/FM-radio-circuit with audio power amplifier. An internal Z-diode stabilizes the supply voltage at VS 13 V, which allows with the aid of a resistor and a rectifier, the circuit to be driven by a higher external supply voltage. Features: Large supply voltage range VS = 3 to 12 V High AM-Sensitivity Limiting threshold voltage Vi = 50 V Audio output power P0 = 0.7 W AFC-connection for VHF-tuner AM-FM switching without high frequency voltages Applications: AM-/FM- and audio-amplifier Circuit Diagram: Circuit diagram for One Chip AM/FM Radio with Audio Power Amplifier Datasheet for TDA1083: Download

2 x 15 W stereo Bridge Tied Load (BTL) audio amplifier

General description: The TDA8946J is a dual-channel audio power amplifier with an output power of 2 × 15 W at an 8 Ω load and a 18 V supply. The circuit contains two Bridge Tied Load (BTL) amplifiers with an all-NPN output stage and standby/mute logic. The TDA8946J comes in a 17-pin DIL-bent-SIL (DBS) power package. The TDA8946J is printed-circuit board (PCB) compatible with all other types in the TDA894x family. One PCB footprint accommodates both the mono and the stereo products. Features: Few external components Fixed gain Standby and mute mode No on/off switching plops Low standby current High supply voltage ripple rejection Outputs short-circuit protected to ground, supply and across the load Thermally protected Printed-circuit board compatible Circuit Diagram: Circuit Diagram for 2 x 15 W stereo Bridge Tied Load (BTL) audio amplifier PCB layout: PCB layout TDA8946 Datasheet for TDA8946J: Download

200W Hybrid Audio Amplifier Circuit

200W Hybrid Audio Amplifier Circuit - c onnecting two TDA2030 thru cheap power transistors we can create a amplifier wich can deliver a higher power. With the components value from the schematic the total amplifier gain is 32 dB. The speaker can be 2 ohm instead of 4 ohm if we use the TIP transistors. TDA 2030 is produced by SGS Ates and is a complete audio amplifier. AB class of the final amplifier cand deliver up to 14W on 4 ohm at a +-14V power supply. With a proper designed power supply this audio amplifier can output 200W. Active components: IC1, Ic2 TDA 2030 T1, T3 = BD 250, TIP 36 T2,T4 = BD 249, TIP 35 D1 … D4 = 1N4001 200W Hybrid Audio Amplifier Circuit

AmplifierCircuits

Search This Blog