TDA1566 Audio Amplifier 2x46W / 1x92W

TDA1566 general description:

The TDA1566 is a car audio power amplifier with a complementary output stage realized in BCDMOS. The TDA1566 has two Bridge Tied Load (BTL) output stages and comes in a HSOP24 or DBS27P package. The TDA1566 can be controlled with or without I2C-bus. With I2C-bus control gain settings per channel and diagnostic trigger levels can be selected. Failure conditions as well as load identification can be read with I2C-bus. The load identification detects whether the outputs of a BTL channel are connected with a DC or AC load and discriminates between a speaker load, a line driver load and an open (unconnected) load. The TDA1566 can be configured in a single BTL mode and drive a 1 Ω load. For the single BTL mode it is necessary to connect on the Printed-Circuit Board (PCB) the outputs of both BTL channels in parallel.  TDA1566 Audio Amplifier 2x46W / 1x92W

TDA1566 features:

• Operates in I2C-bus mode and non-I2C-bus mode
• TH version: four I2C-bus addresses controlled by two pins; J version: two I2C-busaddresses controlled by one pin
• Two 4 Ω or 2 Ω capable BTL channels or one 1 Ω capable BTL channel
• Low offset
• Pop free off/standby/mute/operating mode transitions
• Speaker fault detection
• Selectable gain (26 dB and 16 dB)
• In I2C-bus mode:
• DC load detection: open, short and speaker or line driver present
• AC load (tweeter) detection
• Programmable trigger levels for DC and AC load detection
• Per channel programmable gain (26 dB and 16 dB, selectable per channel)
• Selectable diagnostic levels for clip detection and thermal pre-warning
• Selectable information on the DIAG pin for clip information of each channelseparately and independent enabling of thermal-, offset- or load fault
• Independent short-circuit protection per channel
• Loss of ground and open VP safe
• All outputs short-circuit proof to VP, GND and across the load
• All pins short-circuit proof to ground
• Temperature controlled gain reduction at high junction temperatures
• Fault condition diagnosis per channel: short to ground, short to supply, shorted leadand speaker fault (wrongly connected)
• Low battery voltage detection
• TH version: pin compatible with the TDA8566TH1

TDA1566 circuit:

TDA1566 Audio Amplifier 2x46W

TDA1566 Audio Amplifier 2x46W

TDA1566 layout:

TDA1566 Audio Amplifier 2x46W layout

TDA1566 Audio Amplifier 2x46W pcb

TDA1566 Audio Amplifier 2x46WTDA1566 Audio Amplifier 2x46W pcb

TDA1566 Audio Amplifier 2x46W pcb

TDA8569Q Audio Amplifier 4 x 40W

TDA8569Q general description:

The TDA8569Q is an integrated class-B output amplifier in a 23-lead Single-In-Line (SIL) plastic power package. It contains four amplifiers in Bridge-Tied Load (BTL) configuration, each with a gain of 26 dB. The output power is 4 × 40 W in a 2 Ω load.  TDA8569Q Audio Amplifier 4 x 40W

TDA8569Q features:

Capable of driving 2 Ω loads

Requires very few external components

High output power

Low output offset voltage

Fixed gain

Diagnostic facility (distortion, short-circuit and temperature pre-warning)

Good ripple rejection

Mode select switch (operating, mute and standby)

Load dump protection

Short-circuit safe to ground, to VP and across the load

Low power dissipation in any short-circuit condition

Thermally protected

Reverse polarity safe

Electrostatic discharge protection

No switch-on/switch-off plop

Flexible leads

Low thermal resistance

Pin compatible with the TDA8567Q.

TDA8569Q circuit diagram:

4 x 40W TDA8569Q Audio Amplifier 

TDA8569Q layout:

layout for 4 x 40W TDA8569Q Audio Amplifier 

pcb for layout for 4 x 40W TDA8569Q Audio Amplifier

TA8210AH Audio Amplifier 2x22W

TA8210AH general description:

     It's amizing circuit work beautiful. Is desination for audio amplification, for car. This is a circuit of 2 x 22 watt BTL amplifier using IC TA8210AH. It is not only an auto amplifier, ideal for a low-frequency auditory approach those hi-fi, with a very good linear feature. Can be fueled by a 12 volt car battery but shi from a 12 volt charger. The chip incorporates four bridge amplifiers available in two by two in order to ensure the output 22 watts per channel on 4 ohms. TA8210AH Audio Amplifier 2x22W

TA8210AH features:

• Peak supply voltage (0.2s): 50 V
• supply voltage VCC (DC): 25 V
• Operating supply voltage VCC (opr): 18 V
• Output current (peak): 9 A
• Power dissipation PD: 50 W
• Operating temperature: 30~85 °C
• Storage temperature: 55~150 °C

TA8210AH circuit diagram:

TA8210AH Audio Amplifier 2x22W

TA8210AH layout:

Layout TA8210AH Audio Amplifier 2x22W

PCB TA8210AH Audio Amplifier 2x22W

TDA2005 Audio Amplifier 2x10w

TDA2005 description:

The TDA2005 is a class B dual audio power amplifier in Multiwatt11 package specifically designed for car radio applications. Power booster amplifiers can be easily designed  using this device that provides a high current  capability (up to 3.5 A) and can drive very low  impedance loads (down to 1.6  in stereo  applications) obtaining an output power of more than 20 W (bridge configuration). TDA2005 Audio Amplifier 2x10w

TDA2005 features:

High output power:
Po = 10 + 10 W @ RL = 2 , THD = 10 %
Po = 20 W @ RL = 4 , THD = 10 %.
Protection against:
Output DC and AC short circuit to ground
Overrating chip temperature
Load dump voltage surge
Fortuitous open ground
Very inductive loads
Loudspeaker protection during short circuit for one wire to ground

TDA2005 circuit diagram:

TDA2005 Audio Amplifier 2x10w

TDA2005 layout:

PCB TDA2005 Audio Amplifier 2x10w

Layout TDA2005 Audio Amplifier 2x10w

2 x 50 Watt High Efficiency Power Amplifier

General Description:

     The DDX-2060 power device is a monolithic dual  channel H-Bridge that can provide up to 50 watts  per channel of audio power at very high  efficiency. The DDX-2060 power device contains a logic interface, integrated bridge  drivers, high efficiency MOSFET output transistors and protection circuitry. The device  may be used as a dual bridge or reconfigured as  a single bridge with double the output current capability.  The benefits of the DDX amplification system are  an all-digital design that eliminates the need for a  digital to analog converter (DAC) and the high  efficiency operation derived from the use of Apogee's patented damped ternary pulse width  modulation (PWM). This approach provides an  efficiency advantage over conventional Class-D  designs and up to three times the efficiency of  typical Class A/B amplifiers with music input  signals. 

Circuit Diagram:

Layout 2 x 50 Watt High Efficiency Power Amplifier

Pcb top 2 x 50 Watt High Efficiency Power Amplifier

Pcb buttom 2 x 50 Watt High Efficiency Power Amplifier

Circuit Diagram 2 x 50 Watt High Efficiency Power Amplifier

2 x 40 W car radio power amplifier

FEATURES

Low dissipation due to switching from Single-Ended (SE) to Bridge-Tied Load (BTL) mode

Differential inputs with high Common Mode Rejection Ratio (CMRR)

Mute, standby or operating mode selectable by pin

Load dump protection circuit

Short-circuit safe to ground; to supply voltage and across load

Loudspeaker protection circuit

Thermal protection at high junction temperature

Device switches to single-ended operation at high junction temperature

Clip detection at 2.5 % THD

Diagnostic signal indicating clipping, short-circuit protection and pre-warning of thermal protection.

GENERAL DESCRIPTION

The TDA1565TH is a monolithic power amplifier in a 20-lead heatsink small outline plastic package. It contains two identical 40 W amplifiers. Power dissipation is minimized by switching from SE to BTL mode only when a higher output voltage swing is needed. The device is developed primarily for car radio applications.

Circuit Diagram:

Circuit diagram 2 x 40 W car radio power amplifier

PCB layout:

PCB layout TDA1564 2 x 40 W car radio power amplifier

High efficiency 2 × 25 W/4 Ω stereo car radio power amplifier

FEATURES

Low dissipation due to switching from Single-Ended (SE) to Bridge-Tied Load (BTL) mode

Differential inputs with high Common Mode Rejection Ratio (CMRR)

Mute/standby/operating (mode select pin)

Load dump protection circuit

Short-circuit safe to ground, to supply voltage and across load

Loudspeaker protection circuit

Offset detection for each channel

Device switches to single-ended operation at excessive junction temperatures

Thermal protection at high junction temperature (170°C)

Clip detection at THD = 2.5 %

Diagnostic information (clip/protection/prewarning/offset).

GENERAL DESCRIPTION

The TDA1564 is a monolithic power amplifier in a 17-lead single-in-line (SIL) plastic power package. It contains two identical 25 W amplifiers. The dissipation is minimized by switching from SE to BTL mode, only when a higher output voltage swing is needed. The device is primarily developed for car radio applications.

Circuit diagram:

Circuit diagram  stereo car radio power amplifier

PCB Layout:

pcb layout for High efficiency 2 × 25 W/4 Ω stereo car radio power amplifier

15 W mono Bridge Tied Load (BTL) audio amplifier

General description

The TDA8945S is a single-channel audio power amplifier with an output power of 15 W at an 8 Ω load and an 18 V supply. The circuit contains a Bridge Tied Load (BTL) amplifier with an all-NPN output stage and standby/mute logic. The TDA8945S comes in a 9-lead single in-line (SIL) power package. The TDA8945S is printed-circuit board (PCB) compatible with all other types in the TDA894x family. One PCB footprint accommodates both the mono and the stereo products.

Features

Few external components

Fixed gain

Standby and mute mode

No on/off switching plops

Low standby current

High supply voltage ripple rejection

Outputs short-circuit protected to ground, supply and across the load

Thermally protected

Printed-circuit board compatible.

Applications

Mains fed applications (e.g. TV sound)

PC audio

Portable audio.

Circuit Diagram

15 W mono Bridge Tied Load (BTL) audio amplifier cicuit diagram

Layout and pcb:

15 W mono Bridge Tied Load (BTL) audio amplifier pcb layout

LA4440 Audio Amplifier 2x6w / 1x19W

LA4440 general description:

So it's a very simple audio amplifier based on the LA4440 Integrated Circuits and this will take your computer’s headphone level output and amplify it to drive a pair of external speakers. This project is destinated for all that are listening to music or movies on laptops and computers or car. This circuit uses an LA4440 and some supporting components to give you much more power, while retaining a small package that you can use. The IC is a dual channel audio power amplifier, with low distortion, and a good frequency range.

Using 2 channels, the LA4440 will output 6 watts per channel, that can drive much larger speakers than a laptop can hold. When you set up a small enclosure(s), a 12V power supply, and an audio jack connection to the laptop you’ll have a nice enhancement to your laptop audio enjoyment.

LA4440 features:

• Built-in 2 channels (dual) enabling use in stereo and bridge
• amplifier applications.
• Dual : 6W×2 (typ.)
• Bridge : 19W (typ.)
• Minimun number of external parts required.
• Small pop noise at the time of power supply ON/OFF and good starting balance.
• Good ripple rejection : 46dB (typ.)
• Good channel separation.
• Small residual noise (Rg=0).
• Low distortion over a wide range from low frequencies to high frequencies.
• Easy to design radiator fin.
• Built-in audio muting function.
• Built-in protectors.
• Thermal protector
• Overvoltage, surge voltage protector
• Pin-to-pin short protector

LA4440 specification:

LA4440 circuit diagram sterio:

Stereo Circuit diagram for LA4440 Audio Amplifier 2x6w / 1x19W

LA4440 circuit diagram bridge:

Bridge Circuit diagram for LA4440 Audio Amplifier 2x6w / 1x19W

LA4440 layout:

PCB Layout Circuit diagram for LA4440 Audio Amplifier 2x6w / 1x19W