Audio Amplifier 100W or 130W

ComponentRef./ValueTypeR1 120K 1/4W Resistor

R2 3K3 1/2W Resistor
R3 5K6 1/4W Resistor
R4 3K3 1/4W Resistor
R5 680R 1/4W Resistor
R6 120R 1/4W Resistor
R7 3K3 1/4W Resistor
R8 1K2 1/4W Resistor
R9 2K7 1/4W Resistor
R10 1K5 1/4W Resistor
R11 680R 1/4W Resistor
R12 120R 1/4W Resistor
R13 120R 1/4W Resistor
R14 0,33R 5W Resistor
R15 0,33r 5W Resistor
R16 10R 1W Resistor
R17 10R 1W Resistor
C1 10uF 16V Electrolytic Capacitor
C2 330µF 16V Electrolytic Capacitor
C3 470uF 35V Electrolytic Capacitor
C4 150pF Ceramic Capacitor
C5 100nF 100V Polyester Capacitor
RV1 1K Trimpot
D1 9V1 - 500mW Zener
T1 BC557 PNP transistor
T2 BC557 PNP transistor
T3 BC548 NPN transistor
T4 BD137 NPN transistor
T5 BD137 NPN transistor
T6 BD138 PNP transistor
T7 2N3773 NPN transistor
T8 2N3773 NPN transistor
L1 coil largest number of turns rolled in R16 with AWG22

Comments

One Chip AM/FM Radio with Audio Power Amplifier

Description: The integrated circuit TDA1083 includes, with exception of the FM front end, a complete AM-/FM-radio-circuit with audio power amplifier. An internal Z-diode stabilizes the supply voltage at VS 13 V, which allows with the aid of a resistor and a rectifier, the circuit to be driven by a higher external supply voltage. Features: Large supply voltage range VS = 3 to 12 V High AM-Sensitivity Limiting threshold voltage Vi = 50 V Audio output power P0 = 0.7 W AFC-connection for VHF-tuner AM-FM switching without high frequency voltages Applications: AM-/FM- and audio-amplifier Circuit Diagram: Circuit diagram for One Chip AM/FM Radio with Audio Power Amplifier Datasheet for TDA1083: Download

2 x 15 W stereo Bridge Tied Load (BTL) audio amplifier

General description: The TDA8946J is a dual-channel audio power amplifier with an output power of 2 × 15 W at an 8 Ω load and a 18 V supply. The circuit contains two Bridge Tied Load (BTL) amplifiers with an all-NPN output stage and standby/mute logic. The TDA8946J comes in a 17-pin DIL-bent-SIL (DBS) power package. The TDA8946J is printed-circuit board (PCB) compatible with all other types in the TDA894x family. One PCB footprint accommodates both the mono and the stereo products. Features: Few external components Fixed gain Standby and mute mode No on/off switching plops Low standby current High supply voltage ripple rejection Outputs short-circuit protected to ground, supply and across the load Thermally protected Printed-circuit board compatible Circuit Diagram: Circuit Diagram for 2 x 15 W stereo Bridge Tied Load (BTL) audio amplifier PCB layout: PCB layout TDA8946 Datasheet for TDA8946J: Download

200W Hybrid Audio Amplifier Circuit

200W Hybrid Audio Amplifier Circuit - c onnecting two TDA2030 thru cheap power transistors we can create a amplifier wich can deliver a higher power. With the components value from the schematic the total amplifier gain is 32 dB. The speaker can be 2 ohm instead of 4 ohm if we use the TIP transistors. TDA 2030 is produced by SGS Ates and is a complete audio amplifier. AB class of the final amplifier cand deliver up to 14W on 4 ohm at a +-14V power supply. With a proper designed power supply this audio amplifier can output 200W. Active components: IC1, Ic2 TDA 2030 T1, T3 = BD 250, TIP 36 T2,T4 = BD 249, TIP 35 D1 … D4 = 1N4001 200W Hybrid Audio Amplifier Circuit

AmplifierCircuits

Search This Blog