100w audio amplifier

General description:

 

All resistors are standard metal film 250mW except: R1/3/4/7, these are 2W metal film, and the 0.22ohm beeing 5W. Around R7 is wounded a 0.6mm isolated (enamelled) copper wire forming the output coil. (~12 windings)  For c19 i used 470uf/16v, all other electrolytics 63v. The 10/100/330pF should be mica-caps. The 100nf and 47nf is recommended to be Wima MKS2 (or better), also for C1 i suggest Wima MKS2, 4.7uf is enough. For Trimpot i use a Piher. The MPSA18 can be substituted by BC550C, for all other parts i do not recommend changes, especially the feedback network (r29/30) should be kept unchanged, feedback compensation is very delicate for this circuit ! Be careful when substituting the MPSA18 with BC550C, the pinout is reversed between these 2 transistors !!! The bias is adjusted via the trimpot (R22). Recommended bias is 55ma, resulting in 12mv across a single 0.22ohms or 24mv across both 0.22ohms. Connect a DMM to the upper wires of these resistors and adjust trimpot until DMM reads wanted voltage.

Features:

 

THD: ~0.005% (measured) sim'd: 0.002%
Power into 8ohm: 60 watts
Power into 4ohm: 100 watts
Gain: 32dB (~1:40) full output at 0.7v input (0.5v rms)
Feedback: 57dB
GainBandWidth: ~400Mhz
Slewrate: ~20v/us (symetrical)
Supply voltage: +/- 36v
Biasing: 55ma, ~12mv across a single 0.22 ohm
Measurings:The measuring setup itself is far from perfect, but gives a good idea !
Frequency response: 3.2hz to 145khz (-1db) using 4.7uf input cap
Phaseshift at 10khz: <3°
More will follow !

Circuit Diagram:

100w audio amplifier  circuit diagram

 

Layout Diagram:

100w audio amplifier  layout diagram

Partlist:

Device	Qty	Value	Notes
Q1,Q2	2	MPSA18	can be substituted by BC550C (pins reversed !)
Q7,Q8	2	BC546B	or maybe 2n5551 (pins reversed !)
Q3,Q9	2	2N5551	OnSemi/Fairchild/Philips
Q4,Q5,Q12	3	2N5401	OnSemi/Fairchild/Philips
T1	1	BD139	or bd135, bd135-16
U$5	1	MJE15030	OnSemi
U$6	1	MJE15031	OnSemi
U$3	1	MJL3281A	OnSemi
U$4	1	MJL1302A	OnSemi

Device	Qty	Value	Notes
C14	1	10pF (has been 22pF)	Mica
C2,C7	2	100pF	Mica
C3,C4	2	330pF	Mica
C18	1	47nF	Wima MKS2
C5, C6, C10, C11, C16, C17, C20	7	100nF	Wima MKS2
C1	1	10uF (4.7uF also fits)	Wima MKS2
C8,C9	2	100uF	Electrolytic 63v (at least 40v)
C19	1	470uF	Electrolytic 16v
C12,C13	2	1000uF	Electrolytic 63v (at least 40v)

Device	Qty	Value	Notes
R27,R28	2	0R22	5Watts
R1, R3	2	1R2	2Watts metal film
R4	1	4R7	2Watts metal film
R7	1	10	2Watts metal film
R2	1	10	250mW metal film
R8, R9	2	22	250mW metal film
R31, R32	2	47 (have been 22)	250mW metal film
R26	1	33	250mW metal film
R10	1	68	250mW metal film
R15,R17	2	150	250mW metal film
R11	1	220	250mW metal film
R24,R30	2	499 (or 500)	250mW metal film
R5,R6	2	680	250mW metal film
R13,R23	2	2k	250mW metal film
R12,R14,R29	3	22k	250mW metal film
R18,R20	2	47k	250mW metal film
R22	1	1k pot	Piher, small (470ohm might be better)

Device	Qty	Value	Notes
F1,F2	2	2.5T Fuse	Slow blow
F1,F2	2	---	Fuse holder
L1	1	---	0.6mm isolated (enamelled) copper wire wounded around R7 forming the output coil.

140 watt subwoofer circuit diagram

140 watt subwoofer circuit diagram

100 watt subwoofer for home circuit diagram

Circuit Diagram

1000W Power Amplifier

Circuit Description 1000W Power Amplifier:

Power amplifier has up to 1000 Watt power, this circuit made one channel only so if you want to create a stereo in it must be made one again, actually this is more suitable power amplifier in use for Sound System or outdoor, so if only in use for the house I think is less suitable.

Maybe you've seen or even have an active speaker and there is written 1500 watts PMPO (Peak Music Power Output), make no mistake this is different from Power Amplifier Active Speaker, I often dismantle such Active Speaker in it only a power with power no more than 150 watts by using the transformer 2-3 Ampere. PMPO is not a real power which is issued by the Power Amplifier, but counting all the speakers that there is, for example: if there are 5 pieces of speakers on each channel and each speaker has a power of 10 W then it is 100 W PMPO.

Circuit Diagram 1000W Power Amplifier:

1000W Power Amplifier

Partlist 1000W Power Amplifier:

While this 1000 Watt Power Amplifier minimal use transformer 20 Ampere. And the output of PowerAmplifier DC voltage contains approximately 63 volts, with currents and voltages of this magnitude, this 1000 Watt Power Amplifier will not hesitate hesitate to destroy your woofer speakers to connect. To overcome that then before the speaker on connects to 1000 Watt Power Amplifier must be in pairsSpeaker Protector.

Actually if you want to create a Power Amplifier with great power does not have to make a PowerAmplifier with great power. Example: you want to create a Power Amplifier with 10 000 Watt power. You do not have to assemble a Power Amplifier with power of 10,000 watts, but you assemble thepower Power Amplifier Small but many, such as you assemble the Power Amplifier with 1000 Watts of power for as many as 10 pieces, it will produce 10 000 Watt Power Amplifier helpless.

Circuit uses power transistors pair of 5 x 5 x 2SA1216 and 2SC2922 and 2SC1583 use a differentialamplifier that actually contains 2 pieces of transistors that are in containers together. Why use such built-in amplifier differental tujuanya so identical / similar, could have uses 2 separate transistors but can result in amplifier so it is not symmetrical.

Tips combining speaker.

To get the speakers with great power combining techniques can be used in parallel series, combining each group of speakers should sepaker they will have the same impedance, the same type (Woofer, Mid Range or tweeter) and the same power. Number of merging these speakers should consists of 4 , 9, 16 ff, see picture

Example: The number of speakers have 4 pieces each of its 200 Watt power generated will be aspeaker at = 200 x 4 = 800 Watt. If there are 9 speakers 200 W then the result = 9 x 200 W = 1800Watt.

200 Watt Stereo Car Amplifier

Circuit Description

IC TA8210AH By using this you can apply a series of audio power amplifier is the car audio system. In general, all the speakers in the car using a subwoofer speaker, and woofer. Because the car is not big room so the sound is being required is not too high. Audio amplifier circuit can work at a minimum voltage 12-volt DC, if supplied under voltage 12-voltamplifier work will be less than the maximum. This amplifier output power up to 200W or 2 x 100W stereo with 8 ohm impedance.

Circuit Diagram

200 Watt Stereo Car Amplifier

Part List :

Resistor
R1 =1K
R2 =50K trim
R3 =1K
R4 =50K trim
R5 =680R
R6 =680R
R7 =150K
R8 =2R2
R9 =2R2
R10=2R2
R11=2R2

Capacitor

C1 =1uF
C2 =1uF
C3 =47uF
C4 =47uF
C5 =100n/400V
C6 =220uF
C7 =220uF
C8 =100n/400V
C9 =100n/400V
C10=100n/400V

Intregated Circuit

IC1=TA8210AH

Connector

X2-3=in R
X2-2=gnd
X2-1=in L
X1-1,X1-2=Out R
X1-3,X1-4=Out L

Subwoofer power amplifier IC OPA541BM

Circuit Diagram

Subwoofer power amplifier IC OPA541BM

Amplifier Description

 

Subwoofer power amplifier circuit based on IC OPA541BM very suitable for use in subwoofer speakers, these amplifiers possess excellence in sound issued because the sound is very clear and issued in accordance with subwoofer speakers in a low tone.

Car audio amplifier with IC TA7203P

Circuit Diagram

Car audio amplifier with IC TA7203P

Circuit Description

Stereo car power amplfier with TA7203P , is suitable for the room your car , your car it will build an increasingly crowded and felt like using high-class amplifiers and speakers. Simply using this circuit and some speaker subwoofer speakers you can enjoy it.

Technical information :

• Max voltage = 20 Volt
• Min voltage = 8 Volt
• Max output = 2 x 40 Watt
• RL = 8 Ohm