1000W Power Amplifier

Circuit Description 1000W Power Amplifier:

Power amplifier has up to 1000 Watt power, this circuit made one channel only so if you want to create a stereo in it must be made one again, actually this is more suitable power amplifier in use for Sound System or outdoor, so if only in use for the house I think is less suitable.

Maybe you've seen or even have an active speaker and there is written 1500 watts PMPO (Peak Music Power Output), make no mistake this is different from Power Amplifier Active Speaker, I often dismantle such Active Speaker in it only a power with power no more than 150 watts by using the transformer 2-3 Ampere. PMPO is not a real power which is issued by the Power Amplifier, but counting all the speakers that there is, for example: if there are 5 pieces of speakers on each channel and each speaker has a power of 10 W then it is 100 W PMPO.

Circuit Diagram 1000W Power Amplifier:

1000W Power Amplifier

Partlist 1000W Power Amplifier:

While this 1000 Watt Power Amplifier minimal use transformer 20 Ampere. And the output of PowerAmplifier DC voltage contains approximately 63 volts, with currents and voltages of this magnitude, this 1000 Watt Power Amplifier will not hesitate hesitate to destroy your woofer speakers to connect. To overcome that then before the speaker on connects to 1000 Watt Power Amplifier must be in pairsSpeaker Protector.

Actually if you want to create a Power Amplifier with great power does not have to make a PowerAmplifier with great power. Example: you want to create a Power Amplifier with 10 000 Watt power. You do not have to assemble a Power Amplifier with power of 10,000 watts, but you assemble thepower Power Amplifier Small but many, such as you assemble the Power Amplifier with 1000 Watts of power for as many as 10 pieces, it will produce 10 000 Watt Power Amplifier helpless.

Circuit uses power transistors pair of 5 x 5 x 2SA1216 and 2SC2922 and 2SC1583 use a differentialamplifier that actually contains 2 pieces of transistors that are in containers together. Why use such built-in amplifier differental tujuanya so identical / similar, could have uses 2 separate transistors but can result in amplifier so it is not symmetrical.

Tips combining speaker.

To get the speakers with great power combining techniques can be used in parallel series, combining each group of speakers should sepaker they will have the same impedance, the same type (Woofer, Mid Range or tweeter) and the same power. Number of merging these speakers should consists of 4 , 9, 16 ff, see picture

Example: The number of speakers have 4 pieces each of its 200 Watt power generated will be aspeaker at = 200 x 4 = 800 Watt. If there are 9 speakers 200 W then the result = 9 x 200 W = 1800Watt.

Subwoofer power amplifier IC OPA541BM

Circuit Diagram

Subwoofer power amplifier IC OPA541BM

Amplifier Description

 

Subwoofer power amplifier circuit based on IC OPA541BM very suitable for use in subwoofer speakers, these amplifiers possess excellence in sound issued because the sound is very clear and issued in accordance with subwoofer speakers in a low tone.

PreAmp Subwoofer

Acoustic spectrum is extended by the 20Hz frequency is very low and reaches as high frequency 20000Hz. In the low frequency is lowered sense of direction. This reasoning leads us to attribute to the speaker's use of very low frequency. Making it to you we propose to distinguish these frequencies, in order for him to lead us on a suitable amplifier. Acoustic filter are met at different points in the sound system. Applications knownest they are filter baxandal to organize low-and high-frequency tones and crossover filter where the acoustics are separated in the subareas, for it leads to the appropriate speakers. Applications that you can we propose is a simple filter that limits the acoustic region (20-20000Hz) in 20-100Hz region. With manufacturing, we propose that you can you can make an active filter for you lead a very low frequency loudspeaker. With this you will put a big one between speaker HIFI speakers from you. In order for you to have a complete picture of sound you will need also an appropriate amplifier. In the entry of circuit you will connect the two roads out of the preamplifier or the exit of the preamplifier few. The series production in order to allocate out of the facility led a series of subwoofer power. If for some reason you do not have space for you to put the third speaker in the courtroom, then you can choose a smaller speaker. This output will depend on the type of music that you hear. If in deed you have the space, then after you create a filter and still say thank you, you can he recommend your friends or still makes each other to your friends.

Circuit diagram





Filter | PreAmp Subwoofer circuit diagram

Parts

R1 = 39 Kohm
R2 = 39 Kohm
R3 = 47 Kohm
R4 = 10 Ohm
R5 = 22 Kohm
R6 = 4.7 Kohm
R7 = 22 Kohm
R8 = 4.7 Kohm
R9 = 10 Ohm
R10 = 220 Ohm
C1 = 39 pF
C2 = 0.1 UF
C3 = 0.1 UF
C4 = 0.2 UF
C5 = 0.4 UF
C6 = 0.1 UF
C7 = 0.1 UF
IC1 = TL064

In the form that appears theoretical filter circuit. At first glance we see three different circuits which are mainly produced by two rounds of operational amplifiers. This circuit is a mixture, with the assistance variable amplifier and variable filters. Late-making requires a series of operations catering catering with the same trend with  ± 12. operational amplifier which is the active element for this circuit is the type of dual operation as a TL082 and NE5532. The operational amplifier is included in a family is equipped with field-effect transistor IFET in their entries. Each member is allocated a family in bipolar transistor circuits and field effect. This circuit can function in a high inclination, because of their high propensity to use transistors. Also they have the high honor rhythm elevation (slew rate), low polarization at this time for entry and little influenced by temperature. The operational amplifierhas an area of ​​3MHz unity gain bandwidth. Another important element for them is a great choice reject noise, there are currently in the line of catering.

Price refused to greater than 80dB, their consumption is small, from 11 to 3 mA. They briefly sold internally with eight pins and allocate two operational amplifiers, In the same row 14 pin in short they combine four operations, the trade them for sale with code TL074, TL084 and TL064, a nutshell with eight pins they sold the operational amplifier TL071 TL061 kajTL081 . In manufacturing we use the TL082 that has two operational. First operation of TL082 he worked as an amplifier and mixed with two channels, the entry is negative, it is a little mixed with the two resistances. A potentiometer on the steps of determining the aid circuit. At this point the left wing and right-channel preamplifier they added means of two resistances. En operational continuity with the help strengthen the signal is made depending on the price that has been potentiometer.

PCB layout 

Place runner comparable with the assistance of the circuit. The second operational amplifier is a filter manufacturing. Filters from the acoustic frequency from second grade and he made a round of operational amplifiers. This filter section with variable frequency low-cut. This frequency can be changed and took the price of very low frequency of 30Hz or still exceeds 150Hz. The frequency of the filter depends on the price cuts that have circuit elements. Change the value of the elements that we can have a frequency cut 150Iz, 130Hz, 100Hz, 7A? Z, 6A? Z even 3A? Z, is the price that they can be achieved by simple rotation of the double potentiometer. Filter circuit has been made about an operation 'that has completed a TL082 dual operational amplifier. In the filter out we will connect the plug load which is connected amplifier. In a series of exit are presented, which are limited as to the extent of frequency, the signal applied in the entry of the circuit.

Car Amplifier with IC LA4445

This circuit using IC LA4445 , this is stereo amplifier with power output 2 X 18 Watt, with this circuit you can use to car amplifier or to other elctronics device. Speaker use woofer with impedance 4 Ohm with power up to 20 Watt. Minimum voltagte require 10 Volt and maximum voltage 18 volt.

Car Amplifier with IC LA4445

If you can't operate the circuit , please check IC , and then voltage in. If voltage is good check the component are. If components are working . Please check speakers.

Car amplifier circuit with IC BA532

Minimum Voltage required for this circuit 6 volt and maximum voltage 18 volt . Its can use to amplifier on the electronic devices such us Radio , DVD , MP4 , MP5 , and etc. To amplify the signal sound to audio sound , If you want to bring amplfier you can use the 6V rechargeable battery is able to turn it. What use the rechargeable battery ? because with rechargeable battery when battery runs out , you can charge back.

See Amplifier schematic with IC BA511 below :

Maximum output power 10 Watt with impedance 4 ohm. The circuit is mono amplifier. You can use the circuit to caramplifier because support to low power subwoofer speaker

Car Amplifier Circuit 2 x 30 W stereo

General description:
The TDA8566 is an integrated class-B output amplifier which is available in several packages. TDA8566TH is contained in a 20-lead small outline plastic package. The TDA8566TH1 is a 24-lead small outline plastic package which is pin compatible with the I2C-bus controlled amplifier TDA1566TH for one board layout. TDA8566Q is a 17-pin DIL-bent-SIL package. The device contains 2 amplifiers in a Bridge-Tied Load (BTL) configuration. The output power is 2 × 25 W in a 4 Ω load or 2 × 40 W in a 2 Ω load. It has a differential input stage and 2 diagnostic outputs. The device is primarily developed for car radio applications.

Features:

• Differential inputs
• Very high Common Mode Rejection Ratio (CMRR)
• High common mode input signal handling
• Requires very few external components
• High output power
• 4 Ω and 2 Ω load driving capability
• Low offset voltage at output
• Fixed gain
• Diagnostic facility (distortion, short-circuit and temperature pre-warning)
• Good ripple rejection
• Mode select switch (operating, mute and standby)
• Load dump protection
• Short-circuit proof to ground, to VP and across the load
• Low power dissipation in any short-circuit condition
• Thermally protected
• Reverse polarity safe
• Protected against electrostatic discharge
• No switch-on/switch-off plops
• Low thermal resistance
• TDA8566TH1 is pin compatible with TDA1566TH

Circuit Diagram:

Car Amplifier Circuit 2 x 30 W stereo

Schematic Audio Amplifier with IC TDA2030

This schematic is great for those of you who frequent of use IC TDA2030. In addition to the simple schematic is also very clear , in modification accurate enough to make a sound that is more clear, soft , and loud. And if you interest to try this schematic. See this circuit , datsheet ic TDA2030 and TDA 2040 , and IC TDA2030 equation below :

Schematic Audio Amplifier with IC TDA2030

Datasheet IC TDA2030

Vcc                = 6-18 V

Pout               = 14 W

RL                  = 4 Ohm

Ft                   = 20hz - 20Khz

Icco                = 40 mA

Package         = TO-220

Manufactered = TELEFUNKEN

Datasheet IC TDA2040

Vcc                = 3-20 V

Pout               = 20 W

RL                  = 4 Ohm

Ft                   = 20hz - 20Khz

Icco                = 40 mA

Package         = TO-220

Manufactered = PHILIPS

10 + 10W STEREO AMPLIFIER FOR CAR RADIO

Circuit diagram for 10 + 10W STEREO AMPLIFIER FOR CAR RADIO

STK4050V Power Amplifier Circuit

The project is based around the hybrid integrated circuit power amplifier with STK4050 manufactured by Sanyo to build a low clatter mono audio amplifier with complete peak quality. Explanation The project has a ceiling output power of 200W while incorporating a volume control. The power supplyused participating in the circuit is an on-board type and as of this, barely a hub tapped transformer is considered necessary in place of the powering of the circuit. The sound has a very fine quality and it can stay proven once used in to your place theaters, in computers, and other audio equipments which can as well be used being subwoofer amplifier. On behalf of water down-type audio sets, it can be considered as a compact package. The leg generated arrived thin-type audio sets is being discrete certainly with a good heatsink design. nearby may possibly live reason someplace a shock din may be encountered especially for the period of switch ON and switch inedible. This can be summary by only if a constant current circuit. The design of the circuit can be tailored used for sinking occurrence of thermal shutdown, brief circuit protection for oodles, shock racket muting from exterior power supply. The load resistance besupposed to arrange 8 Ohms profit with 55K Ohms input impedance.

LM317 Amplifier Circuit

You probably know with the purpose of LM317 IC is used being an changeable voltage manager, but did you know it can take place used as an audio amplifier? This is a taste A audio amplifier built with LM317 so as to delivers a utmost 1W audio power. Manipulate a worthy heatsink pro the LM317 IC and adjust the 5K inconsistent resistor so with the aim of you allow 4.5V on 10Ω resistor (otherwise LM317 pin 2, Vout).

3 Watt stereo amplifier circuit

3 Watt stereo amplifier circuit using MAX 7910 IC. The MAX9710 a stereo audio power amplifier IC capable of delivering 3Watts of out put to 4 Ohm loads. MAX9710 can be operated from a single 4.5V to 5.5V power supply , makes it ideal for hand held applications.The IC for 3 Watt stereo amplifiercircuit also features thermal overload protection. This 3 Watt stereo amplifier circuit is suitable for small power audio devices such as radio sets and portable CD players. 5 V DC power supply is used for powering the 3 Watt stereo amplifier circuit. 6V battery with an IN 4007 diode series to the positive terminal of it can also be used instead of 5 V DC supply. The 3 Watt stereo amplifier circuit will get a supply voltage approximately 5 V after 0.7 V voltage drop across diode.

BTL Stereo Amplifier TDA7052

This is BTL stereo power amplifier with basic amplifier on IC TDA7052 / TDA7053

TDA7294 150 W Power Amplifier

Description of bridge TDA7294:

This is power amplifier based on IC TDA7294 with output power 150W with 8 ohm impedance, source voltage + - 25V. for circuit see image below.
Circuit diagram for TDA7294:

TDA7294 150 W Power Amplifier

200W power amplifier complete power supply

This 200W power amplifier circuit using IC STK 4050.

STK 4050 is a power amplifier module is very powerful, because the IC is already a module then only needed a little extra components to build a reliable 200W Power Amplifier. Here is a picture series of Power Amplifier ICs 200W use STK 4050 complete with its power supply

Surround Amplifier Circuit with TDA7053

Perhaps the surround amplifier circuit below is an interesting circuit is made. For, making easy just by using the IC and electrolytic capacitor added 1 , we already can hear the strains of music with sound ( Front Left ,Right and surround Right , Left. In addition to listening to music , this amplifier is also very suitable for gamers who want good sound quality. Minimum voltage requred 9 volts and maximum of 15 volts. Power Output of each speaker 10 Watt with 4 ohm impedance.

Surround Amplifier Circuit with TDA7053

Good Quality Sound Amplifier Circuit

This amplifier circuit has a pretty good quality. Of course the sound quality, although this one amplifier does not have a large output power but in terms of soft and loud voice that this amplifier can be unreliable. With a single IC capitalize MPC576H and several other supporting components you have to make this amplifier circuit. Voltage at least 9 Volt and 24 Volt Max. Output Power 3.5 Watts with 8 Ohm impedance.

                         

Good Quality Sound Amplifier Circuit

100W Digital-Amplifier Power Stage 6-Channel

Subwoofer filter Circuit

Circuit to solve new to the buffer input for the signal R + L and cutting area of ​​the Muting issue and the cut-off point often fear for VR 4 floor hard so I divided into 2 layers using 2 the time that the cut frequency, if wanted. It has layers of fine cut to the same location. I use ic tl072. And replace series capacitor 0.022 with 0.047 . That a soft voice that sounds good offline but not feeling heavy and dial around the back lot, try changing the capacitor. Beyond the traditional. Intended to adjust to extremely low frequency adjustment for the store before so I think that the device is used. Could differ. I sent in this condition before.

5000W High Power Amplifier Circuit

300W Subwoofer Amplifier